pilot light wont stay lit on furnace

eusebio-cordes-geraci June 28, 2022 furnace , light , wallpaper , wont Comment

There are a couple of other things it might be. This component is a heat sensor that regulates the gas valve that runs to the pilot light.

Pin On Hvac

Your pilot light depends on a consistent gas source to keep the flame going.

. If the pilot tube is dirty let the furnace cool down and turn off the gas. A furnace pilot light wont stay lit after the thermocouple because the pilot burner is unclean or the gas valve is not activating. Turn off the gas valve shut off the furnace and call a professional.

If you have other gas appliances with pilot lights check them to see if their flames are also struggling. Why does this happen. Attempts to re-light the pilot light are futile.

Once you release the button now if the pilot light still doesnt persist to stay lit- then its perhaps time for a general furnace check-up. Then soak the burner in soapy water for 30 minutes. Begin by turning your pilot light off if it is not already.

It wont stay on. Furnace Pilot Light Keeps Going Out. If the pilot light wont stay lit on furnace another common issue is a dirty thermocouple.

770 872-4171 Request An Appointment. Once it has cooled the. The thermocouple is a part of this procedure.

When a pilot light keeps going out you may try to relight it. The first two causes a dirty gas orifice and an issue with the thermocouple account for 90 of pilot flame issues. The common problems with your pilot light on your furnace and how to fix a broken pilot light explained by furnace repair experts in Massillon Ohio.

However if you find yourself doing this frequently the thermocouple could be dirty. When my pilot light wouldnt stay lit on my furnace I asked a few plumber buddies about the symptoms and they both said it was the thermo couple. The thermocouple operates by closing the gas when the pilot light goes out.

A good furnace pilot light will ensure the safe and comfortable functioning of your furnace. If after a full minute the flame goes out when you let go of the safety the pilot may be dirty. This occurs because the thermocouple doesnt hold the magnet open allowing for the gas valve to work.

A dirty pilot tube can also prevent the pilot from staying lit. Dalton330 832-5848 Dalton330 832-5848. Then light the pilot flame and wait for a few seconds until the thermocouple heats up.

In simple terms the thermocouple checks to see if your pilot light flame is lit and turns off the gas. It senses heat from the pilot light flame closing. Then clean it and the surrounding area and replace it.

Your home has a natural gas regulator that can affect the gas supply to all gas appliances. To fix the problem shut down the furnace turn off the gas supply and take off the burner heads. Issues with the gas valve whether its malfunctioning or just dirty can cause the flame to go out.

In some cases a gas pilot light can sometimes go off just from a wind gust or breeze knocking it out. When you replace the thermocouple these dirty furnace parts may just attract. To do so turn off the gas supply and use a screwdriver to remove the valve.

If the pilot light still wont stay lit remove the old valve and install a new one making sure its tightly screwed. When this happens youll want to clean it properly. Its best to clean the pilot burner using a wide-bristled brush and change the gas valve.

If you have made several attempts to light your pilot and it does not light or stay lit you may not be holding the safety in long enough. In This HVAC Training Video I Show UP CLOSE How the Thermocouple Pilot Light and Gas Valve Work on a Water Heater Furnace Fireplace as well as other Ap. A dirty pilot burner and orifice prevent the pilot light from burning.

A furnace thermocouple is a safety feature that regulates gas flow to your system based on whether the pilot light is on. The most common reasons the furnace pilot light wont stay lit. However if not in the on position pop the breakers back.

It should be nearby or even on your furnace. In case your gas water heaters pilot light is working and it remains lit but not the burner make sure that the circuit breaker panels and the furnace itself are in the on position. Replacing the thermocouple may only have a little to do with this issue.

Make sure that you are holding the safety on for at least a full minute. If your furnace has a pilot light it wont work if the light continues to burn. Before conceding the cost of emergency repairs and calling an HVAC professional read ahead for some of the most common reasons why your furnace pilot.

If the furnaces pilot light wont stay on the furnace wont work. Its also possible that the supply of gas has entirely run out. Next turn off the flow of gas to your furnace completely using the shutoff valve.

The clue to this cause is that the pilot light lights easily after being out and stays lit for a few hours to a day or more. The most common reason why your furnace pilot light wont stay lit is dirty furnace parts. First shut off your gas wait for the unit to cool.

Common causes include the furnaces thermocouple and pilot tube. Once you have done this allow your furnace to cool down for at least 30 minutes so it is safe to open then open the hatch covering your pilot light and. If all of the pilot lights are going out frequently or are weak the gas regulator might be providing low or inconsistent gas supplies to your appliances and needs to be.

Blocked burners are often the result of dirt buildup due to poor maintenance. The flame should be blue and if it. Maybe the pilot stays on for a moment and the furnace attempts to fire but almost immediately shuts down.

Sometimes a simple solution like this is an answer to why your furnace wont kick on. Why Wont My Furnace Pilot Light Stay Lit.

How To Fix A Water Heater Pilot Light Hot Water Heater Repair Water Heater Heater